Hotline: +6587995589 | Email: hello@activeplumbing.sg
Your Trusted Plumber Singapore
faucet | water tap leakage
A dripping faucet is annoying and can also be a waste of water and money! If you have a leaking tap, don't wait to fix it. Most of the modern faucets have a cartridge, the main purpose is to control the switch water source, for the mixer tap, it can adjust the mode of cold water and hot water.
The cause of leaking faucets is usually due to old or worn cartridges or the main body, some can be repaired but most of them need to be replaced with new faucets.
Kitchen sink taps, bathroom washbasin taps, shower mixer taps, washing machine taps. Home garden faucets are just a few examples of the applications for which a fixture may be used. It's critical to ensure an institution is correctly positioned to avoid plumbing issues like leaking taps.
Reasons for Leaking Taps | Faucet
The Cartridge
Your water supply line is made up of your cartridge, which is one of the essential components of your tap. It can be harmed by mishaps or wear and tear over time. If you don't know how a faucet works, replacing a cartridge is straightforward.
The Valve Seat
The most susceptible portion of the spout is where it meets the tap. Mineral build-upbuild-up or everyday wear and tear can harm this area over time. A leaking faucet may be quickly fixed due to a valve seat, allowing quick repair.
Loose Parts
Because the components in your tap are loose, it might leak due to a faulty faucet. Try tightening movable parts, such as washers and O-rings, to see if the issue goes away. If you still can't fix the problem after trying everything else, it's time to call a plumber.
Hard Water Buildup
Corrosion on the rubber washers meant to prevent leaking faucets may be observed in areas with a lot of pollutants in the water. This leads to a dripping faucet in the end.
The Washer
The most common source of tap leaks is this tiny rubber or leather ring, which pushes down on the end of your water pipe to prevent water from flowing. They can rust, become damaged with time, or not have been installed correctly in the first place.
The O-Ring
This component, inserted into your tap handle, creates a waterproof seal. These may be damaged or come off, resulting in water leaking near the end of your tap's handle.
Excessive Water Pressure
Low water pressure is often to blame for leaking taps. Water cannot efficiently flow from one place to another if the pressure is excessively high. Pipes become clogged with water as a result of this. As a consequence, your faucets will leak.
Pipe Issues
The water pressure might be high for various reasons, including corrosion, fractures, and root damage. Water pressure varies due to multiple factors, including rust, cracks, and root damage. Several more indicators indicate that you may have plumbing difficulties, such as unusual odors or water with significant leaks that are colored weirdly.
Faulty Tap | Faucet Repair
Leaks are easy to repair, so you don't need to call a plumber unless it's an emergency. Check out our tutorial on fixing a broken faucet if you're good at resolving issues like this. If you're caught while repairing and can't continue because of a lack of access, consider enlisting the help of non-emergency plumbing services.
Instruments
The first thing you'll need is the following items. If the problem is severe, you may not require all the equipment. Examine if any of the causes above for a leaking faucet apply to you. Repairing it will take approximately an hour if done correctly. Here's a list of things you could want:
- Flathead screwdriver
- Scouring pad
- White vinegar
- WD-40 (Lubricant)
- Philips head screwdriver
- Adjustable wrench
- Replacement parts
Turn The Water Supply Off
Always turn the water off before attempting a leaking faucet repair. If you leave the main shutoff valve open after turning it off, you will end up with a flooded toilet or kitchen. The water supply can usually be stopped at the shutoff valves, which are generally beneath the sink. Alternatively, you may use the main supply valve to switch off the entire home's water supply. Ensure all faucets are closed to allow for proper pressure release from the supply lines by covering them with a stopper. Cover it with a plug to prevent small parts from entering the drain.
Dismantle The Leaking Faucet Handles
It is now time to utilize the equipment. Remove any decorative handles from the faucets with a flathead screwdriver. Then remove the screws that hold the handle using a Philips head screwdriver. If any components appear rusted or difficult to remove, lubricate them with WD-40, and they will become more pliable. Put aside all of the parts except for one, on which you should write a note so you can identify which ones go together later.
Examine The Faucet Parts
Remove the packing nut from the valve stem with a wrench to expose it. With pliers or a screwdriver, twist or pry off the valve stem. Check for signs of corrosion or build-upbuild-up on the packing nut and stem. Also, check the O-ring and washer in the valve seat to ensure they are still functioning. If any part is unclean, clean it as needed and then set it aside with a note indicating so.
Sterilize The Valves
Check the valves after all components have been removed from the faucet. Mineral deposits or build-upbuild-up may be evident around the valve. This is when white vinegar comes in useful. Apply a layer of white vinegar over the deposit area and let it sit for 10-15 minutes. The solution will dissolve the deposit, allowing it to be easily eliminated after being soaked with scouring soda; washing the valves with clean water will remove any debris or dirt accumulated.
approach